Fix Common Vaping Issues: A Complete Troubleshooting Guide

For many smokers and enthusiasts, vaping has evolved as their preferred substitute. Like any tool, vapes occasionally run into issues that could compromise your experience, though. This tutorial will help you troubleshoot and resolve the most often occurring vaping problems, regardless of the burned taste, leaking tank, or low vapour output.

1. Burnt Taste Vaping-Based

Origin:

Coil that is dry or worn out
High wattage ranges
Not enough e-liquid in the tank.
Not appropriately priming the coil

Correction:

Drizzle a few drops of e-liquid straight onto the cotton within a new coil. Let it sit five to ten minutes following tank filling.
Check the suggested wattage range of your coil and make necessary changes.
Always make sure your tank contains enough juice to correctly soak the coil.
Replace your coil if it still tastes burnt even if it has been used for some time.

2. Leaking in Vape Tanks

Origin:

Oversawing the tank
O-rings that are loose or damaged
Incorrect PG/VG ratio
Problems with coil installation

Correction:

Make sure e-liquid doesn't pass into the centre airflow tube and avoid overfilling.
Examine the rubber seals and replace them should they be cracked or loose.
Should you be using a very thin e-liquid—high PG—it could leak more. For thicker consistency, try a higher VG e-liquid.
Make sure it is correctly screwed in but not very tight since overtightening may thread damage.

3. Weak or non-vapor production

Reason:

Low charge of battery
blocked airflow
malfunctioning or ancient coil
wrong wattage settings

Correction:

Make sure the battery of your gadget is running as it should be completely charged.
Use a cotton swab to wipe any trash or obstructions found in the airflow vents.
Should your coil have been overused, it might not generate enough vapour.
Make sure your gadget is set to the proper wattage range according to from the coil manufacturer.

4. Strong or fiery throat hit

Cause:

High nicotine concentration
PG in your e-liquid is too much.
Chain vaping causes overheating
Burn out of coils

Correction:

If you use high-nicotine e-liquids, try moving to a lower strength.
As PG offers a stronger throat punch, try an e-liquid with more VG.
Let some time separate puffs to avoid dry hits and overheating.
A burned coil might produce a bad throat hit. Replace it as needed.

5. Problems with gurgling or spit back

Agent:

Surplus e-liquid in the coil
Oversampling the coil
inundated tank

Corrections:

Remove the coil and softly blow through it to empty extra e-liquid.
Steer clear of overpriming by priming just using a few drops of e-liquid.
To stop too much liquid from getting into the mouthpiece, slightly boost the airflow.
Press the fire button once for a second then draw to eliminate any extra liquid without inhaling.

6. Vape Not Firing

Causes:

Problems with battery connections
broken firing button
Activate the safety lock.

Mend:

Using a dry towel, wipe the battery connection points.
Many mods include a safety lock for your device. Five rapidly clicks the fire button to unlock.
Should the button be stuck or non-functional, your gadget might require expert repair.
Try changing to a fresh battery if you use an external battery mod.

7. E-Liquid Taste Notes Mild

Agent:

Vaper's tongue, or transient taste loss
Insufficient e-liquid taste
Worn-out coil

Mend:

To clear your palate and stop dry mouth, sip water.
Try a different flavour; rotating tastes helps your taste receptors reset.
Replace the coil; over time, a worn-out coil could mute tastes.
A higher VG base helps some flavours be more noticeable.

Finally

Though most of them are simple to fix with some troubleshooting, vaping problems can be annoying. Using the correct e-liquids, keeping coils, and properly caring for your equipment can help to guarantee a flawless and pleasurable vaping experience. Should issues continue despite your efforts at these remedies, think about contacting your local vape shop or manufacturer for more help.